Fiberglass Buyers Guide (Car Craft, March 1956): Part 6 – The Sorrell SR-100 Sports Car

This is a picture of the Dick Lane's Sorrell SR-100 From '55 - on a Kurtis 500 Chassis, no Less!

Hi Gang…

This is our sixth in a series of “spotlights” on sections of a Buyer’s Guide for fiberglass sports cars published by Car Craft in March, 1956.  Click on the link below to review all fiberglass cars discussed in this 1956 Buyer’s Guide as of today:

Click here to review all articles published on the Car Craft, March 1956 Buyer’s Guide

Today’s article focuses on the Sorrell SR-100 Sports Car designed by Bob Sorrell which debuted in November 1953 at the Petersen Motorama in Los Angeles, California.

Background: Sorrell SR-100 Sports Cars

We have lots to share on the Sorrell SR-100 so hold onto your fiberglass hats in the near future.  Bob Sorrel was born in 1927 and was 26 years old when his first car debuted in 1953.  He went on to make two different size bodies like this and also offered the larger of the two bodies in aluminum.

Dick Jones, Meteor SR1 designer and builder, shared a story with me a few years ago about how the first Sorrell body was built.  Dick knew Bob Sorrell and went to California Metal Shaping to see his latest project.  Dick remembered what he saw because it was quite unusual (at least he thought at the time).

“What I remembered, Geoff, was that they were creating two bodies at once out of aluminum.  I hadn’t seen that before.  The shop would put two aluminum sheets together and tack them (weld).  They would then shape the metal over the buck and then untack the sheet and ‘presto” they had two panels – not one.

They fit each sheet to a skeleton of stations and each sheet was then welded to the next.  Bob wanted to keep one body and sell the other to pay for the first.  The fiberglass mold was then taken off this ‘first’ aluminum body.”

So…we’ve seen the original bucks used for our fiberglass built from plaster (Glasspar G2 and others), clay (Victress S4, Grantham Stardust, and others), and now aluminum (Sorrell SR-100).  These guys were creative and entrepreneurial in every way gang!

Sorrell Engineering:

I have several pieces from “Sorrell Engineering” that I’ll share in the near future.  One of these pieces gives detailed information about the history of the company.  Let me share a bit with you now:

“The Sorrell Engineering firm has been designing and building sportscar bodies since 1942.  In 1952, the first fiberglass body was produced.  The design was sketched in perspective on the drawing board and from that design quarter scale drawings were made.

Full-scale cross-sections were developed and a wood mock-up was produced and delivered to the metal shapers for rough forming.  Two aluminum skins of .0625 were produced in the rough, then it took four months to complete one metal body.  Interior and exterior templates were made to assure a precision finished body:  the SR-100.

The firm specializes in sportscar styling and building.  The bodies are constructed of fiberglass or metal.  Aluminum bodies are our specialty, however, to fit the average pocketbook, we make several bodies in fiberglass.  The SR-100 in either roadster, competition or coupe.  The SR-190 in coupe only.

We also make a line of fiberglass tops for MG, Jaguar, Allard, Porsche and Austin-Healyy (prototype).  We are making a Cooper Streamliner type body.”

So…enjoy this segment of Car Craft’s 1956 Fiberglass Buyers Guide and be on the lookout for the next Sorrell hiding out there.  Just a few have been found, and your efforts could make you the next lucky owner.  And you’d make Bob Sorrell very proud.

Go get ‘em gang!

Car Craft (March 1956): The Sorrell SR-100 Sports Car

Car Craft (March 1956)
Sorrell SR-100 Sports Car
Specifications

Wheelbase
  • 95 to 100 inches
Tread – Front
  • 56 inches
Tread – Rear
  • 58 inches
Overall Length
  • 173 inches
Overall Width
  • 69  inches
Overall Height at Cowl
  • 36 inches
One Piece Body Shell Only
  • $500.00
Other stages of body completion and accessories are available at extra cost.
For additional prices and information, write: Sorrell Engineering
9616 Felton Street
Inglewood, California
Orchard 7-1402

Summary:

Hope you enjoyed the story, and until next time…

Glass on gang…

Geoff
——————————————————————–
* Click on the following link to view all stories on:  Sorrell Sports Cars
——————————————————————–
* New Feature: To post your comments and thoughts about this story, scroll down the page and post your information in the section titled “Leave A Reply.”  Your name and e-mail address will be required, but only your name will appear – not your e-mail address.

* Click here to visit the Forgotten Fiberglass Forums and post your thoughts about vintage fiberglass cars.

* Click here to review the “Forgotten Fiberglass Vision Statement” as well as our “Approach to Research

* Click here to listen to our Podcast led by Todd Ruel of Gone Autos

* Click here to visit our Forgotten Fiberglass Facebook page

* Don’t Forget: We appreciate any and all donations to our Forgotten Fiberglass website.  Your donations help defray production costs.  To make a donation, look for the “Support Forgotten Fiberglass” box at the bottom right of our website and click on the word “Donate”.  All contributions help make “Forgotten Fiberglass” the best it can be.
——————————————————————-
Click on the Images Below to View Larger Pictures
——————————————————————-


Comments

Fiberglass Buyers Guide (Car Craft, March 1956): Part 6 – The Sorrell SR-100 Sports Car — 2 Comments

Leave a Reply

Your email address will not be published. Required fields are marked *